Een FPC-goudvinger is een verguld kopercontact aan het uiteinde van een flexibele print. A ZIF connector is a zero insertion force connector that clamps the flexible circuit after insertion. A stiffener is the bonded reinforcement that sets the final tail thickness and keeps the FPC straight during assembly.
Kort samengevat
- Match the connector drawing for 0.20 mm or 0.30 mm finished FPC thickness.
- Use hard gold over nickel when the product needs repeated insertion cycles.
- Keep the stiffener edge, vias, and first bend away from the contact wipe zone.
- Define contact width, pitch, chamfer, exposed length, and plating thickness on the drawing.
- Inspect thickness and plating before assembly, not after intermittent failures appear.
Design focus
The contact tail must be designed from the connector drawing, not only from the PCB footprint. Check pitch, contact length, insertion depth, actuator clearance, tail width, and side-guide tolerance. For fine-pitch connectors, even 0.10 mm offset can move the FPC array away from the spring contact center.
See related guidance on FPC connector selection, stiffener design, and bend radius rules.
"A 0.30 mm ZIF connector with a 0.24 mm finished FPC tail may pass a bench continuity check, but the contact force margin is already weak before vibration testing."
— Hommer Zhao, Engineering Director at FlexiPCB
Plating and stiffener choices
| Finish | Best use | Typical cycle target | Main risk | Note |
|---|---|---|---|---|
| Hard gold over nickel | Serviceable modules | 20-100+ | Higher cost | Strongest wear margin |
| ENIG | Internal low-cycle ZIF | 1-20 | Wear under rubbing | Good for one-time assembly |
| Immersion tin | Very low-cost devices | 1-5 | Oxidation | Avoid for service contacts |
| Carbon ink | Special low-cost contacts | Application-specific | Higher resistance | Confirm with connector supplier |
| Bare copper | Temporary test only | 0 | Oxidation | Not for production |
Hard gold over nickel is preferred when the FPC may be inserted many times. ENIG is often acceptable for an internal connector inserted once during factory assembly. Reference IPC electronics standards, ISO 9000, and polyimide when defining quality and material controls.
"For 0.50 mm pitch tails, control pad width, pitch, array offset, and finished tail width separately. Electrical test cannot catch a mechanically off-center contact array."
— Hommer Zhao, Engineering Director at FlexiPCB
Factory lesson
In a 2026 pilot lot of 2,400 FPC tails for a sensor module, a 0.06 mm spread in bonded tail thickness changed ZIF contact force after thermal cycling. The fix was tighter adhesive control and a 1.5 mm longer FR4 stiffener support, not a new connector.
"The connector tail is not a free bend zone. Treat the first moving section as a separate flex beam with its own radius, copper, and strain review."
— Hommer Zhao, Engineering Director at FlexiPCB
FAQ
What finished thickness should the ZIF tail use?
Use the connector drawing. Common values are 0.20 mm and 0.30 mm, often with about +/-0.03 mm tolerance.
Is ENIG enough for gold fingers?
For one-time internal assembly, yes in many products. For more than 20 insertions, specify hard gold over nickel.
How long should exposed contacts be?
Many connectors use 2.0-4.0 mm exposed length, but the exact value must match insertion depth and wipe area.
Should the stiffener be PI or FR4?
Polyimide is thinner and more flexible. FR4 gives stronger handling support for many 0.30 mm ZIF tails.
Can vias sit near the contact area?
Avoid vias in the contact, insertion, and stiffener transition zone. Keep at least 1.0-2.0 mm clearance, more near bends.
CTA
Voor een maakbaarheidscheck kunt u FlexiPCB contacteren of een offerte aanvragen.
