Een flex PCB kan elektrisch kloppen en toch in RFQ mislopen als de einddikte vaag is. Bij een wearable sensor in 2026 stond 0,20 mm nominaal op de tekening, terwijl de ZIF-connector 0,30 +/-0,03 mm toeliet.
Kort samengevat
- Stack-up thickness là độ dày hoàn thiện của đồng, polyimide, keo, coverlay, mạ và stiffener cục bộ.
- Hãy định nghĩa riêng cho đuôi ZIF, vùng uốn động, vùng stiffener và chuyển tiếp rigid-flex.
- IPC-2223 và IPC-6013 hữu ích, nhưng bản vẽ vẫn cần giới hạn đo được như 0.30 +/-0.03 mm.
- Thay đổi keo 25 micron có thể dịch neutral axis và làm giảm biên độ tuổi thọ uốn.
Definition and standards
Flex PCB is a flexible printed circuit built on a bendable dielectric, usually polyimide. Stack-up thickness includes copper, dielectric, adhesive, coverlay, surface finish, and local stiffeners after lamination. Drawings often cite IPC standards, especially IPC-2223 and IPC-6013, but the RFQ must still name the local thickness that matters.
"When a flex drawing says only total thickness, I ask: total where? At the bend, connector tail, stiffener, or rigid-flex transition, the answer can differ by more than 0.20 mm."
— Hommer Zhao, Engineering Director at FlexiPCB
Four-zone thickness map
The bend zone controls copper strain. The ZIF tail controls connector latch force. The stiffener island controls SMT coplanarity. The rigid-flex transition controls delamination risk. Use one table on the fabrication drawing and connect it with the bend radius guide, rigid-flex transition rules, and gold finger design guide.
Decision table
| Zone | Finished target | RFQ tolerance | Main risk | First-article proof |
|---|---|---|---|---|
| Dynamic single-layer bend | 0.075-0.125 mm | +/-0.025 mm | Copper fatigue below 100,000 cycles | Bend coupon + cross-section |
| Double-sided flex | 0.15-0.25 mm | +/-0.03 mm | Via stress and stiffness | Thickness report |
| ZIF tail | 0.20-0.33 mm | Often +/-0.03 mm | Loose latch or high insertion force | Tail gauge check |
| FR-4 stiffener | 0.40-1.00 mm | +/-0.05 mm | Poor coplanarity | Bond inspection |
| Impedance zone | Solver-defined | State dielectric tolerance | Impedance beyond +/-10% | TDR coupon |
Material and impedance risk
A 25 micron adhesive layer can be 15-25% of a thin bend stack. For dynamic designs, compare adhesiveless flex PCB, but remember that coverlay and stiffener adhesive remain. For high-speed FPC, thickness also changes impedance; pair the RFQ with the impedance control guide and impedance coupon guide.
"For dynamic flex, I do not approve a stack-up from total thickness alone. I want copper type, copper thickness, adhesive thickness, coverlay thickness, and copper position in the bend."
— Hommer Zhao, Engineering Director at FlexiPCB
"Tight tolerance is not a substitute for a workable stack-up. If a supplier must sort parts by hand to hit the connector window, change the construction."
— Hommer Zhao, Engineering Director at FlexiPCB
References
FAQ
What is a normal flex PCB thickness?
Single-layer dynamic flex often finishes at 0.075-0.125 mm. Double-sided flex often lands at 0.15-0.25 mm. ZIF tails must follow the connector datasheet.
Should nominal or finished thickness be specified?
Both. Use nominal layer values for manufacturing and finished zone tolerance after lamination and plating, such as 0.30 +/-0.03 mm.
How does thickness affect bend radius?
Thicker flex places copper farther from the neutral axis, so the bend radius must increase. IPC-2223 is commonly used as design guidance.
Does adhesiveless laminate remove thickness risk?
No. It removes base adhesive, but coverlay adhesive, stiffener adhesive, and plating still need measurement.
When is a cross-section required?
Use it for rigid-flex transitions, impedance coupons, high-reliability dynamic bends, or narrow ZIF thickness windows.
DFM review
Request a flex PCB DFM review before tooling to confirm finished thickness, bend risk, connector-tail fit, and first-article evidence.
