FPC-kabelsamling til 3D-vision er en kameraforbindelse med FPC-tail, fine-pitch-stik, kabelføring, afskærmning og elektrisk verifikation.
RFQ gennemgår Samtec 1x20/1x10, 100mm routing, NDA, testgrænser og prøveplan.
Prøver planlægges normalt på 2-4 uger, når tegning, BOM, stiktilgængelighed og rapportkrav er klare.
IPC-A-620, UL-758 og IATF 16949 knyttes til workmanship, ledningsdokumentation, sporbarhed og change control.
FPC-kabelsamling til 3D-vision es una interconexión de cámara que combina cola FPC, conector de paso fino, ruta de cable, blindaje y verificación eléctrica. Un cable de cámara Samtec es una pieza controlada por PN, altura de acoplamiento, conteo de pines y dirección de cierre; si esos datos cambian, cambia el riesgo de fabricación. El abastecimiento bajo NDA protege tegning, BOM, archivos 3D y límites de prueba hasta aprobar al proveedor. En RFQ revisamos disponibilidad de conector, espesor de cola, salida de flexión, reglas de etiqueta, continuidad o señal, IPC-A-620, UL-758 e IATF 16949.
Use when camera routing, Samtec pin count, 100mm cable path, NDA gate, and test evidence must be closed before tegning release.
Moving camera modules need cable exit, service loop, and stik retention reviewed before produktion.
Procurement can request sample reports, traceability, packing photos, and approved alternates before 100-120 stk. batches.
For confidential modules, supplier qualification can finish before files are shared; quotation follows quickly after BOM and tegning.
When Samtec or equivalent parts constrain schedule, datasheets are compared and validation samples can be built before substitution.
Confirm NDA, factory background, certifications, data-security expectations, and approved recipients for tegning, BOM, and 3D files.
Engineering reviews Samtec PN, mating connector, pin map, cable length, FPC tail thickness, bend exit, strain relief, labels, and alternates.
The quotation separates sample MOQ, pilot MOQ, connector sourcing, fixture assumptions, report format, open drawing issues, and lead time.
The prøve run verifies mating, length, routing, continuity, insulation resistance when required, inspection criteria, labels, and packing.
After buyer validation, pilot lots lock revision control, approved components, report format, packaging, replacement rules, and change-control flow-down.
Supplier qualification, IP control, and RFQ review happen before confidential camera tegning enters the factory.
Samtec 1x20/1x10, mating height, latch direction, and approved alternates are checked before prøve release.
The RFQ can include continuity reports, inspection photos, COC, traceability, and sample evidence instead of only a unit price.
10 samples, 100-120 stk. pilots, and repeat orders keep the same revision, fixtures, labels, and component approvals.
Public links explain the standards families; the released drawing, purchase specification, and inspection plan remain the acceptance authority.
IPC-A-620 is used when the drawing needs cable workmanship language for connector termination, solder, strain relief, routing, inspection, and acceptance records. IPC reference
UL-758 is reviewed when procurement asks for recognized wire insulation, AWM context, or material evidence for the cable portion of the assembly. UL reference
IATF 16949 flow-down is relevant when vision systems enter automotive, robotics, or industrial OEM supply chains that require traceability and change control. IATF reference
Anonymized cases show the supplier-side details that affect quote confidence for vision and automation buyers.
A 3D vision and industrial measurement OEM required strict IP protection before sharing files. The supplier had to pass headquarters and supply-chain review, execute the NDA, then quote the released cable package without losing the launch window for Danmark og nordisk maskinbygning.
Concrete numbers: 3-month vetting phase, 1x20 Pin Samtec connector, 1x10 Pin Samtec connector, 100mm cable length, 4-week lead time
A South American industrial automation distributor needed rapid technical validation, equivalent connector and terminal options, and sample testing before moving first orders into production.
Concrete numbers: 100-120 unit batches, 2-3 weeks lead time after payment, 5 connector/housing variants per assembly
Complete inputs let engineering quote connector, FPC, cable path, and test risk instead of guessing.
Send camera cable tegning, FPC or Gerber data, BOM, Samtec or equivalent PN, mating connector data, target MOQ, sample quantity, and annual forecast.
Include cable length, 100mm or custom routing, exit direction, bend path, service loop, shield or drain requirement, label location, and packing rules.
Provide NDA requirements, AVL restrictions, country-of-origin concerns, test limits, fixture method, inspection class, and required reports.
Share previous failures, rejected samples, connector shortage history, or supplier notes when the RFQ is a recovery or transfer project.
The response is structured for procurement, engineering, and quality review before PO release.
MOQ, prøve lead time, production lead time, connector sourcing status, fixture needs, tooling assumptions, and open risks.
DFM notes covering Samtec interface, FPC tail, bend exit, routing, strain relief, label rules, packaging, and missing dimensions.
Quality plan listing IPC-A-620, UL-758 when requested, IATF 16949 flow-down, continuity testing, inspection records, COC, and traceability.
If tegning or BOM is incomplete, the response separates firm pricing from assumptions so buyers can compare suppliers without hidden risk.
Plan on 10 engineering samples when tegning, BOM, connector PN, cable length, and test limits are complete. Pilot batches commonly start around 100-120 stk. after the buyer approves mating, fixture method, label rules, packaging, and inspection records.
Simple samples are normally planned at 2-4 uger after NDA release, drawing freeze, connector availability, and test limits are clear. Stable small-to-medium production can run in 2-3 weeks, while Samtec sourcing, fixture work, or formal qualification can push planning toward 4 weeks.
We can discuss capability, typical lead time, certification flow-down, and what data will be needed, but accurate pricing needs the controlled drawing package. For IP-sensitive 3D vision modules, the NDA and approved recipient list should be finished before full BOM and geometry release.
Use IPC-A-620 for cable workmanship, add IPC-A-610 if soldered FPC or PCBA interfaces are included, request UL-758 wire evidence when recognized insulation data matters, and specify IATF 16949-style traceability or change control when the assembly enters automotive or regulated OEM supply chains.
Quote drift usually comes from missing connector PNs, incomplete mating data, unclear cable length, undefined bend exit, changing labels, unavailable Samtec parts, or test limits added after pricing. We mark those assumptions in the RFQ response so procurement can close the gaps before PO release.
Yes. Send the original PN, mating connector, pin count, mechanical envelope, electrical limits, and AVL restrictions. We compare datasheets, identify fit or locking risks, and can build sample assemblies for buyer validation before a substitute appears in production.
Use these references for terminology context; production acceptance follows your released drawing and purchase specification.
IPC context helps frame cable workmanship, soldered FPC interfaces, strain relief, inspection language, and supplier documentation.
UL background helps procurement understand when UL-758 wire recognition or AWM evidence matters for a cable assembly.
IATF 16949 context is useful when camera and automation cables require supplier flow-down, traceability, and change control.
Supplier-side RFQ experience for FPC-kabelsamling til 3D-vision: FPC, cable, connector, test, documentation, and confidentiality risk.
FlexiPCB engineering and RFQ reviewer
Hommer Zhao reviews flex PCB, rigid-flex, and FPC cable assembly programs for OEM procurement teams. For FPC-kabelsamling til 3D-vision, the review focuses on NDA control, Samtec availability, FPC tail geometry, cable routing, continuity evidence, sample timing, and production change control before the first PO.
Factory KPI
Case-bank RFQ included 3-month vetting phase, 100mm cable length, and 4-week lead time
Sample path
10 engineering samples before 100-120 stk. pilot batches when tegning and BOM are complete
Standards
IPC-A-620, UL-758, IPC-A-610 when soldered interfaces apply, ISO 9001:2015, IATF 16949:2016 flow-down
Documentation
DFM notes, COC, continuity report, inspection photos, traceability, and approved-substitute records
