Assemblage de câble FPC pour vision 3D

Samtec 1x20/1x10, 100mm cable path, NDA control, and échantillon evidence for vision OEMs.

Pour une équipe d’approvisionnement qui qualifie des câbles caméra pour l’automatisation, le prix unitaire ne suffit pas. Un cas réel a exigé la protection de la propriété intellectuelle avant toute transmission de fichiers; après le NDA, le dossier contenait 1x20 Pin Samtec connector, 1x10 Pin Samtec connector, 100mm cable length et 4-week lead time. La revue doit couvrir FPC, câble, connecteur, essais, traçabilité et planning avant le premier achat.

ISO 9001|ISO 13485

Engineering review before quotationPrototype through volume productionTest report and traceability support

Assemblage de câble FPC pour vision 3D — flexible printed circuit board

En bref

Un assemblage de câble FPC pour vision 3D relie une caméra avec queue FPC, connecteur fin, routage câble, blindage et vérification électrique.

La RFQ valide Samtec 1x20/1x10, chemin 100mm, NDA, limites de test et calendrier d’échantillons.

Les échantillons sont généralement planifiés en 2-4 semaines quand dessin, BOM, connecteur et rapports sont clairs.

Applicable IPC and UL requirements are reviewed alongside customer-specific automotive traceability, documentation, and change-control requirements.

À envoyer avec votre RFQ de câble de vision 3D

Applicable IPC and UL requirements are reviewed alongside customer-specific automotive traceability, documentation, and change-control requirements.

Factory case: 3-month vetting phase, 1x20 Pin Samtec connector, 1x10 Pin Samtec connector, 100mm cable length, 4-week lead time.

Canada et Amérique du Nord: useful for 3D vision heads, industrial measuring cameras, robotics vision modules, and compact inspection equipment.

Engineering checks FPC tail geometry, Samtec mating data, connecteur orientation, bend radius, shielding, labels, and fixture method.

échantillon samples usually start at 10 engineering pieces; pilot lots move to 100-120 pièces after dessin and BOM control.

Documentation can include DFM notes, COC, continuity report, inspection photos, traceability, and approved-substitute records.

Tableau des capacités

Build scopeFPC tail + camera cable + Samtec 1x20/1x10 or equivalent connecteur + label + electrical test

Typical cable path100mm reference path from case bank; custom routing, exit direction, and service loop reviewed per drawing

MOQ10 engineering samples; 100-120 pièces pilot batches; production MOQ confirmed after connector and fixture review

Sample lead time2-4 semaines after NDA, dessin, BOM, connector availability, and test limits are complete

Production lead time2-3 weeks for stable small-to-medium batches; 4 weeks when Samtec sourcing, NDA approval, or fixtures add review steps

Connector reviewSamtec 1x20/1x10, JST, Molex, TE, board-to-wire, FPC/ZIF, candidate alternates with datasheets

Electrical checksContinuity, pin map, insulation resistance when required, signal-path review, fixture method and report format

Workmanship referenceIPC-A-620 cable workmanship with IPC-A-610 review when soldered FPC or PCBA interfaces are included

Compliance flow-downISO 9001 and ISO 13485 quality systems remain available where applicable, with customer-specific automotive documentation, traceability, and change-control requirements.

RFQ outputMOQ, sample timing, production timing, connector risk, tooling assumptions, test evidence, and open engineering questions

Vision 3D et mesure industrielle

Use when camera routing, Samtec pin count, 100mm cable path, NDA gate, and test evidence must be closed before dessin release.

Caméras robotisées

Moving camera modules need cable exit, service loop, and connecteur retention reviewed before production.

Inspection usine et métrologie

Procurement can request sample reports, traceability, packing photos, and approved alternates before 100-120 pièces batches.

Qualification fournisseur sous NDA

For confidential modules, supplier qualification can finish before files are shared; quotation follows quickly after BOM and dessin.

Plan de secours connecteur

When Samtec or equivalent parts constrain schedule, datasheets are compared and validation samples can be built before substitution.

NDA et qualification fournisseur

Confirm NDA, factory background, certifications, data-security expectations, and approved recipients for dessin, BOM, and 3D files.

Revue connecteur et DFM

Engineering reviews Samtec PN, mating connector, pin map, cable length, FPC tail thickness, bend exit, strain relief, labels, and alternates.

Offre et risques ouverts

The quotation separates sample MOQ, pilot MOQ, connector sourcing, fixture assumptions, report format, open drawing issues, and lead time.

Échantillons et preuves

The échantillon run verifies mating, length, routing, continuity, insulation resistance when required, inspection criteria, labels, and packing.

Pilote puis production répétée

After buyer validation, pilot lots lock revision control, approved components, report format, packaging, replacement rules, and change-control flow-down.

Pourquoi les OEM vision confient FPC, câble et connecteur au même fournisseur

NDA control

Supplier qualification, IP control, and RFQ review happen before confidential camera dessin enters the factory.

Connector discipline

Samtec 1x20/1x10, mating height, latch direction, and approved alternates are checked before échantillon release.

Production evidence

The RFQ can include continuity reports, inspection photos, COC, traceability, and sample evidence instead of only a unit price.

Controlled scale-up

10 samples, 100-120 pièces pilots, and repeat orders keep the same revision, fixtures, labels, and component approvals.

Références publiques des normes

Public links explain the standards families; the released drawing, purchase specification, and inspection plan remain the acceptance authority.

IPC-A-620 workmanship

IPC-A-620 is used when the drawing needs cable workmanship language for connector termination, solder, strain relief, routing, inspection, and acceptance records. IPC reference

UL-758 wire evidence

UL-758 is reviewed when procurement asks for recognized wire insulation, AWM context, or material evidence for the cable portion of the assembly. UL reference

Automotive-grade quality controls

Automotive programs follow customer-specific quality, traceability, documentation, and change-control requirements. Automotive-grade quality controls

Preuves d’application réelle

Anonymized cases show the supplier-side details that affect quote confidence for vision and automation buyers.

NDA-first 3D vision qualification

A 3D vision and industrial measurement OEM required strict IP protection before sharing files. The supplier had to pass headquarters and supply-chain review, execute the NDA, then quote the released cable package without losing the launch window for Canada et Amérique du Nord.

Concrete numbers: 3-month vetting phase, 1x20 Pin Samtec connector, 1x10 Pin Samtec connector, 100mm cable length, 4-week lead time

Initial automation cable order

A South American industrial automation distributor needed rapid technical validation, equivalent connector and terminal options, and sample testing before moving first orders into production.

Concrete numbers: 100-120 unit batches, 2-3 weeks lead time after payment, 5 connector/housing variants per assembly

Our Shenzhen SMT factory26 placement machines · 11 SMT lines4 nitrogen reflow ovensAI-assisted 3D SPI & AOI, MES-linked01005 placement in mass production

See our Shenzhen factory

Envoyez le dessin caméra, PN Samtec, BOM, NDA et prévisions

Send your Gerber, drawing or spec — a flex-PCB engineer replies with a DFM-checked quote and lead time. No bounce to another page: submit right here.

Free DFM-checked quote — no obligation
Low MOQ — prototype to volume
Built to IPC standards with ISO 9001 / ISO 13485 quality systems
NDA on request — files kept confidential

Get a Free DFM-Checked Quote

Upload your Gerber, drawing or spec. A flex-PCB engineer replies with a DFM-checked quote and lead time.

À envoyer avec votre RFQ de câble de vision 3D

Complete inputs let engineering quote connector, FPC, cable path, and test risk instead of guessing.

Send camera cable dessin, FPC or Gerber data, BOM, Samtec or equivalent PN, mating connector data, target MOQ, sample quantity, and annual forecast.

Include cable length, 100mm or custom routing, exit direction, bend path, service loop, shield or drain requirement, label location, and packing rules.

Provide NDA requirements, AVL restrictions, country-of-origin concerns, test limits, fixture method, inspection class, and required reports.

Share previous failures, rejected samples, connector shortage history, or supplier notes when the RFQ is a recovery or transfer project.

Ce que vous recevez

The response is structured for procurement, engineering, and quality review before PO release.

MOQ, échantillon lead time, production lead time, connector sourcing status, fixture needs, tooling assumptions, and open risks.

DFM notes covering Samtec interface, FPC tail, bend exit, routing, strain relief, label rules, packaging, and missing dimensions.

Applicable IPC and UL requirements are reviewed alongside customer-specific automotive traceability, documentation, and change-control requirements.

If dessin or BOM is incomplete, the response separates firm pricing from assumptions so buyers can compare suppliers without hidden risk.

What MOQ should we plan for 3D vision FPC cable samples?

Plan on 10 engineering samples when dessin, BOM, connector PN, cable length, and test limits are complete. Pilot batches commonly start around 100-120 pièces after the buyer approves mating, fixture method, label rules, packaging, and inspection records.

How long do samples and production usually take?

Simple samples are normally planned at 2-4 semaines after NDA release, drawing freeze, connector availability, and test limits are clear. Stable small-to-medium production can run in 2-3 weeks, while Samtec sourcing, fixture work, or formal qualification can push planning toward 4 weeks.

Can you quote before the NDA is complete?

We can discuss capability, typical lead time, certification flow-down, and what data will be needed, but accurate pricing needs the controlled drawing package. For IP-sensitive 3D vision modules, the NDA and approved recipient list should be finished before full BOM and geometry release.

Which standards should we list on the drawing?

Applicable IPC and UL requirements are reviewed alongside customer-specific automotive traceability, documentation, and change-control requirements.

What causes quote drift on camera cable programs?

Quote drift usually comes from missing connector PNs, incomplete mating data, unclear cable length, undefined bend exit, changing labels, unavailable Samtec parts, or test limits added after pricing. We mark those assumptions in the RFQ response so procurement can close the gaps before PO release.

Can alternate connectors be validated?

Yes. Send the original PN, mating connector, pin count, mechanical envelope, electrical limits, and AVL restrictions. We compare datasheets, identify fit or locking risks, and can build sample assemblies for buyer validation before a substitute appears in production.

Références publiques des normes

Use these references for terminology context; production acceptance follows your released drawing and purchase specification.

IPC electronics standards

IPC context helps frame cable workmanship, soldered FPC interfaces, strain relief, inspection language, and supplier documentation.

View IPC reference

UL safety organization

UL background helps procurement understand when UL-758 wire recognition or AWM evidence matters for a cable assembly.

View UL reference

Automotive-grade quality controls

Automotive programs follow customer-specific quality, traceability, documentation, and change-control requirements.

Automotive-grade quality controls

Revue d’ingénierie usine

Supplier-side RFQ experience for Assemblage de câble FPC pour vision 3D: FPC, cable, connector, test, documentation, and confidentiality risk.

FlexiPCB Engineering Team

FlexiPCB engineering and RFQ reviewer

FlexiPCB's engineering team reviews manufacturability, documentation, and production risk for flex PCB and cable-assembly programs.

Factory KPI

Case-bank RFQ included 3-month vetting phase, 100mm cable length, and 4-week lead time

Sample path

10 engineering samples before 100-120 pièces pilot batches when dessin and BOM are complete

Standards

ISO 9001 and ISO 13485 quality systems remain available where applicable, with customer-specific automotive documentation, traceability, and change-control requirements.

Documentation

DFM notes, COC, continuity report, inspection photos, traceability, and approved-substitute records

Assemblage de câble FPC pour vision 3D

En bref

À envoyer avec votre RFQ de câble de vision 3D

Tableau des capacités

Vision 3D et mesure industrielle

Vision 3D et mesure industrielle

Caméras robotisées

Inspection usine et métrologie

Qualification fournisseur sous NDA

Plan de secours connecteur

NDA et qualification fournisseur

NDA et qualification fournisseur

Revue connecteur et DFM

Offre et risques ouverts

Échantillons et preuves

Pilote puis production répétée

Pourquoi les OEM vision confient FPC, câble et connecteur au même fournisseur

NDA control

Connector discipline

Production evidence

Controlled scale-up

Références publiques des normes

IPC-A-620 workmanship

UL-758 wire evidence

Automotive-grade quality controls

Preuves d’application réelle

NDA-first 3D vision qualification

Initial automation cable order

Envoyez le dessin caméra, PN Samtec, BOM, NDA et prévisions

Get a Free DFM-Checked Quote

À envoyer avec votre RFQ de câble de vision 3D

Ce que vous recevez

What MOQ should we plan for 3D vision FPC cable samples?

How long do samples and production usually take?

Can you quote before the NDA is complete?

Which standards should we list on the drawing?

What causes quote drift on camera cable programs?

Can alternate connectors be validated?

Références publiques des normes

IPC electronics standards

UL safety organization

Automotive-grade quality controls

Revue d’ingénierie usine

FlexiPCB Engineering Team

Nos Services

PCB Flexible

PCB Rigide-Flexible

Assemblage PCB Flexible

Assemblage Rigide-Flexible

Prototype PCB Flexible

PCB Flex HDI

Raidisseur pour PCB Flexible

Fini de Surface Flex PCB

Flex PCB à impédance contrôlée

Flex PCB multicouche

PCB Flex Bus CAN

PCB flexible à doigts d'or

Instant PCB Quote

Flex PCB Box Build Assembly

Assemblage de câble pour PCB flexible

Assemblage de connecteurs FPC

Assemblage de câble FPC surmoulé

Assemblage de câble micro-coaxial pour FPC

Assemblage de câble FPC pour capteurs robotiques

Assemblage de pigtail FPC

Assemblage de câble FPC LVDS